audio/pipewire-spa-oss-ng 0.9.12_2

lang/rust: Bump revisions after 1.99.0

PR:		299016

lang/rust: Bump revisions after 1.98.1

PR:		298139

audio/pipewire-spa-oss-ng: Update to 0.9.12

Match FreeBSD's scaled PCM secondary-buffer policy and cache
nonuniform silence fills so larger rings remain allocation-free on
the data loop.

Stabilize native timer readiness coverage, harden checked SPA FFI
pointers, and refresh Rust dependencies.

audio/pipewire-spa-oss-ng: Update to 0.9.11

Harden live FreeBSD OSS behavior: reconnect devd monitors, improve
busy-owner diagnostics, probe exclusive rates without consuming PCM
channels, keep capture nonblocking, correct mixer state, release streams
on Suspend, and guard setup-phase streams from a live queue-sampling
assertion that could abort the data thread.

Expand OSS format support, cache companded silence fills, stabilize
adaptive scheduling, and adopt libc's typed FreeBSD ioctl helpers.

lang/rust: Bump revisions after 1.97.1

PR:		296645

audio/pipewire-spa-oss-ng: Update to 0.9.10

Use oss APIs for channel mapping

audio/pipewire-spa-oss-ng: Update to 0.9.9

Improve playback timing and OSS event handling: avoid locked polling on
audio cycles, use enriched kqueue events for wakeups (with an optional
timer-based path), retain partial writes, retune without inserting
silence, and keep queued playback across Pause.

Generate format-correct PCM silence and harden host input and reentrant
event handling on the device and node paths.

audio/pipewire-spa-oss-ng: Update to 0.9.8

Advertise signed 24-bit, 32-bit float, and unsigned 8-bit PCM formats when
the OSS device or feeder supports them, alongside the existing 16- and
32-bit integer formats. Negotiation order, frame widths, and bitperfect
filtering are covered by tests.

Register per-module SPA log topics (spa.oss.device, .sink, .source,
.monitor) so PIPEWIRE_DEBUG='spa.oss.*:LEVEL' filters the plugin's output,
matching the spa.alsa convention.

Internally the FFI surface was reworked - unsafe confined to small kernels,
cross-loop device rebuilds moved onto owned messages instead of shared
state pointers, and the implementation organized by subsystem - with no
change to the audio path.

audio/pipewire-spa-oss-ng: Update to 0.9.7

Keep the device byte stream frame-aligned across short writes and reads.

audio/pipewire-spa-oss-ng: Update to 0.9.6

pin EnumFormat stereo last so Pulse volume width stays stable after idle
(device close and reopen shows volume slider on Plasma6).

audio/pipewire-spa-oss-ng: Update to 0.9.5

Retune in place across graph quantum changes

audio/pipewire-spa-oss-ng: Update to 0.9.4

Capture (source) fixes for cramped rings and fat strides

Fixes a field report of skipping audio when recording and playing back
at once on a fat-stride USB capture device (20-channel S32, 80
bytes/frame): FreeBSD clamps the soft ring at CHN_2NDBUFMAXSIZE, so it
holds only ~1.6 graph periods there, and the capture path had no
headroom for arrival jitter.

audio/pipewire-spa-oss-ng: Update to 0.9.3

Fixes a field report of periodic drops with crackles on USB audio: the
sink's near-full fill branch keyed on small driver-forced fragments as a
proxy for a small total buffer, which uaudio breaks (1 ms soft fragments,
large grant) - near-full targeting added 100+ ms of latency and left one
fragment of overshoot headroom, so every normal servo excursion
short-wrote and dropped the tail.

Validated by a discrete-event simulation of the servo (exact DLL and
bandwidth-adaptation ports) that reproduces the field failure with the
old target and shows zero drops with the new one across +/-2000 ppm
drift, jitter storms and 4-hour runs, plus the live battery on hdspe(4).

audio/pipewire-spa-oss-ng: Update to 0.9.2

robustness fixes, driver-clock overhaul, hardware volume control

audio/pipewire-spa-oss-ng: Update to 0.9.1

Threading / robustness:
- Serialize all reconfiguration onto the data loop and stop the driver
  timer cleanly on pause/suspend (closes the renegotiation window behind
  a PipeWire audioconvert crash).
- Detach loop sources and close the timerfd on clear().
- Fail negotiation instead of aborting when the device won't open or
  rejects the format/channels/rate; validate peer-provided formats and
  buffers; return errors from all unhandled SPA entry points.
- Run without devd (hotplug disabled instead of aborting).

Audio / OSS:
- Probe device caps and advertise real formats, rates and channel
  layouts (mono through 7.1 in FreeBSD kernel interleave order, plus
  the device's native width as AUX channels).
- Open capture read-only so asymmetric play/rec channel counts work
  (shkhln/pw-oss#3).
- Run a DLL on capture: real clock delay/rate_diff and rate matching;
  prime capture with silence and a drained ring at startup.
- Report OSS underruns/overruns via the xrun callback.

Params / session:
- Store and replay the port Latency param; ProcessLatency and
  latencyOffsetNsec support.
- Device profiles (Off/Default) with node add/remove.
- Source port param parity: Format readback, Buffers info, re-emit.
- oss.delay: PropInfo entry, Props readback, per-device defaults via
  monitor.oss.rules, live re-apply.
- Log through the spa.oss topic (PIPEWIRE_DEBUG=spa.oss:N).

audio/pipewire-spa-oss-ng: New port

PipeWire SPA plugin implementing a FreeBSD OSS backend, tracking the
pw-oss fork at https://github.com/kev009/pw-oss.

Changes over upstream shkhln/pw-oss:

Audio / OSS:
- Size the OSS buffer to the device and fix data-loop aborts.
- Adapt the fill target to the device's real fragment size.
- Report clock delay and rate; require MemPtr buffers.
- Reset the channel before close so close() doesn't block draining.
- Close the device when the format is cleared.
- Advertise and re-emit the port Format param (ALSA-sink pattern).
- Don't abort the process on an oversized chunk or a bad/unpositioned
  format.

Session / config:
- Don't launch a second WirePlumber from exec.conf; the stock config
  already starts one, and the duplicate bricked audio.

Packaging / dependencies:
- Refresh all dependencies; migrate to libspa 0.10 (its pod builder
  now returns rustix::io::Errno).
- Rename the crate to spa-freebsd-oss-ng; the installed
  libspa_freebsd_oss.so is unchanged.
- Add package metadata and install docs for the
  audio/pipewire-spa-oss-ng port.
- Quiet clippy and dead_code warnings.

Conflicts with audio/pipewire-spa-oss as both install the same files.