sysutils/u-boot-rpi3 2026.10

sysutils/u-boot-*: Update to 2024.01

Sponsored by:	Beckhoff Automation GmbH & Co. KG

sysutils/u-boot-rpi*: Fix sd boot after v2023.10 update

U-Boot update broke sd boot for rpi* models, use upstream patch that fixes it.

PR:		275655
Sponsored by:	Beckhoff Automation GmbH & Co.KG

sysutils/u-boot-master: Update to 2023.10

Sponsored by:	Beckhoff Automation GmbH & Co. KG

sysutils/u-boot: Update to 2022.04

sysutils/u-boot-*: Add patch to fix MMC ordering

For FreeBSD we use a dtb overlay that switches between the sdhost and
the sdhci controller for sd card.
Recent changes in u-boot device model changed device numbering and the
sd card controller became "mmc2" for our setup which isn't accounted for
in the possible boot devices.
Patch isn't accepted yet upstream but bring this patch in for our ports anyway.

One more small cleanup, forgotten yesterday. Reported by:	lwhsu

Remove # $FreeBSD$ from Makefiles.

Remove references to non existent patches.

PR:		250723

u-boot: Update to 2020.07

Remove upstreamed patches.

Add sysutils/u-boot-rpi3-32 to build a 32-bit version of u-boot

This is useful for using the camera hardware, as
misc/raspberrypi-userland does not support aarch64.

Approved by:	imp, manu
Differential Revision:	https://reviews.freebsd.org/D21603

sysutils/u-boot: Update to 2020.04

While here use python3 for it as it now works.
Two slave ports have been marked broken :
u-boot-pandaboard and u-boot-duovero
Both of those boards have ~0 users in FreeBSD so if you are one of
those raise your hand.

sysutils/u-boot-rpi{3,4}: Add patch to fix PSCI stub reservation

For the traditional spin table setup, only the lowest page needs
to be reserved.  However, our PSCI stubs are slightly bigger and occupy
a little over one page.  These patches, already sent upstream, allow a
variable number of initial pages to be reserved for the SMP stubs.  We
then set the values for these in our fragment to '2' to reserve the first
and second page.

Approved by:	koobs (mentor)
Approved by:	manu (uboot, maintainer)
MFH:		2020Q1
Differential Revision:	https://reviews.freebsd.org/D24085

Use HTTPS as possible

Update U-Boot to 2019.01

This removes a lot of local patches

Approved by:	bapt (mentor, implicit)

Minor cleanup of u-boot's patches

Move to using the 'raw' patches for those patches that are currently
in u-boot's upstream landing zone.  Move to using a u-boot directory
since the numeric names aren't very u-boot specific and might
conflict. Bump PORTREVISION out of an abundance of caution.

Differential Review: https://reviews.freebsd.org/D16409

Remove MAINTAINER lines. They are set by the master port and all these ports are maintained by the uboot@ mailing list.

Approved by: uboot@ (maintainer of these ports)
Differential Review: https://reviews.freebsd.org/D16397

Revert r475122, r475123 and r475124.

To manage upstream, we use the exact patches we've submitted upstream
via their patchwork server. This deviates a little from a standard
port, but it's what we do with all the other u-boot ports and isn't
grossly out of line (many other ports pull patches during the build).
We do it this way because the standard way was an unmanageable
nightmare and resulted in divergence of u-boot ports.

Approved by: uboot@ (maintainer of these ports)
Differential Revision: https://reviews.freebsd.org/D16397

Use patchfiles that are in accordance with accepted Ports Collection usage.

Add patchfiles that are in accordance with accepted Ports Collection usage.

u-boot: Update to v2018.07

This add:

 - Explicit Depency on bison
 - Remove the DTC= on MAKE_ARGS as we use the BINARY_ALIAS already
 - metadata variables
 - Add cache cmds and disable secure boot
 - All RPI uses some special fragments to enable OF_BOARD.
   This makes u-boot using the DTB loaded by the firmware instead of
   using it's own.
 - For patches accepted but not in mainline due to timing issue use patchwork
   directly instead of putting files in the port
 - All armv7 boards are EFI enabled and boot in secure mode

More on metadata file :

The goal is to have a u-boot-install package that will read those and auto
install u-boot either on a dir (method copy) or on a device (method raw)
As all the u-boots are either one file to be dd'ed or one/multiple files
to be copied this simple method is good enough.
Since the maximum variable is 4 (for the raw method), simply use echo instead
of a .in files (ok bapt@)

Reviewed by:	imp
Approved by:	imp (implicit)
Differential Revision:	https://reviews.freebsd.org/D16241

- due to a miscommunication the patch files were not added

Convert to use u-boot-master as per Phabricator D14630 Reassign to uboot team

Bump PORTREVISIONs of all users of math/mpc that we just updated to version 1.1.0 (via revision 464079).

Do not overwrite WRKSRC when USE_GITHUB=nodefault.

Sponsored by:	Absolight
Differential Revision:	https://reviews.freebsd.org/D10091

Typo forgot :uboot

Reported by:	pkg-fallout

Use github for psci monitor  [brd] Chase upstream Redo save_boot_params in lowlevel__init.S to add reserve_memory remove save_boot_params from rpi.c Note network code diffs are now upstreamed already

PR:		ports/216757
Submitted by:	brd

Add gonzo's psci monitor code to support RPI3 SMP

Update to 2016.11 upstream

Remove stray uneeded patch files.

Initial u-boot port for the Raspberry Pi 3